사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASME PTC 4-2013
Fired Steam Generators (PTC 4 - 2013)- 발행일 : 2013-01-01
- 발행기관 : ASME
상세정보
| 분야 | PTC : Performance Test Code |
|---|---|
| 적용범위 | This Code provides rules and instructions for conducting performance tests of fuel fired steam generators. These include coal, oil, and gas fired steam generators as well as steam generators fired by other hydrocarbon fuels. The scope also includes steam generators with integral fuel-sulfur capture utilizing chemical sorbents. Steam generators which are not fired by coal, oil, or gas may be tested using the concepts of this Code, but it should be noted that the uncertainty caused by variability of the fuel may be difficult to determine and is likely to be greater than the uncertainties in sampling and analysis of coal, oil, or gas. For example, gas turbine heat recovery and other heat recovery steam generators designed to operate with supplemental firing should be tested in accordance with PTC 4.4. Testing of auxiliary equipment is not addressed in this Code, but are covered PTC 4.2, PTC 4.3 and PTC 11. This Code does not prescribe procedures for testing to determine chemical and physical properties of fuels. This Code specifically addresses equipment used for the generation of steam; however, the basic principles presented are also applicable to other working fluids. Certain types and sizes of equipment used for the recovery of heat released by combustion are not addressed in any specific Performance Test Code. This Code can be used as a general guide in developing performance tests for such equipment; however, such specifically developed performance tests shall not be considered ASME Code tests. This Code provides general procedures for conducting combustible fuel fired steam generator performance tests; however, it cannot possibly provide detailed procedures applicable to every steam generator design variation. Design variations considered in developing this Code include subcritical and supercritical once-through steam generators and oil, gas, stoker, cyclone, pulverized, and fluidized bed firing. For each performance test, a competent engineer must study the actual steam generator and its relation to the remainder of the steam cycle, and develop test procedures which are consistent with this Code. A test report shall be prepared. Many references, which are listed in this Code, provide useful supplemental information in planning for a performance test in accordance with this Code. |
| 국제분류(ICS)코드 | |
| 페이지수 | 284 |
| Edition |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASME PTC 4-2013상세보기 | Fired Steam Generators (PTC 4 - 2013) | 2013-01-01 | 표준 |
| 2 | ASME PTC 4-2008상세보기 | Fired Steam Generators (PTC 4 - 2008) | 2008-01-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ISO 1940-1:2003 - Mechanical vibration — Balance quality requirements for rotors in a constant (rigid) state — Part 1: Specification and verification of balance tolerances
- ASME PTC 46-2015 - Overall Plant Performance
- ASME PTC 11-2008(R2018) - Fans (PTC 11 - 2008)
- ASME PTC 1-2015 - General Instructions (PTC 1 - 2015)
- ISO 5801:2017 - Fans — Performance testing using standardized airways
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)