한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    폐지

    판매

    B340-18

    Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2
    • 발행일 : 2018-01-01
    • 발행기관 : CSA
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]HARDCOPY 464,300원

상세정보

분야
적용범위 Preface This is the seventh edition of CSA B340, Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2. It supersedes the previous editions, published in 2014, 2008, 2002, 1997, 1988, and 1986. This Standard is one of a series of Standards adopted by reference by the Transportation of Dangerous Goods Regulations. Because the Regulations might adopt this Standard with certain exceptions or additional requirements, they should be consulted to determine where they differ from the requirements of this Standard. Notwithstanding the provisions of this Standard, compliance with the provisions of the Transportation of Dangerous Goods Act and the Regulations thereto can call for additional requirements due to particular characteristics or properties of individual dangerous goods. Any requirements of the Transportation of Dangerous Goods Regulations regarding the handling, the offering for transport, and the transportation of dangerous goods in cylinders, spheres, and tubes are to be fully complied with. The Technical Committee on Cylinders, Spheres, and Tubes for the Transportation of Dangerous Goods, which is responsible for this Standard, has maintained close links with Transport Canada to ensure compatibility of the new edition of this Standard with the amended Transportation of Dangerous Goods Regulations. The Technical Committee has also reviewed and made extensive use of the Compressed Gas Association publications and the US Code of Federal Regulations. This edition of CSA B340 incorporates numerous amendments and refinements to the previous edition, while retaining the same basic format. Changes to the seventh edition include the following: a) new provisions to authorize the use of specification DOT containers; b) new provisions to authorize the use of containers manufactured in accordance with grandfathered U.S. DOT special permits and exemptions; c) new provisions allowing containers to be requalified, repaired, reheat treated, and rebuilt outside of Canada in accordance with the U.S. DOT’s 49 CFR; and d) new provisions for vacuum-insulated closed containers for helium refrigerated liquid. Scope 1.1 This Standard covers safety requirements for the selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2. 1.2 This Standard covers requirements for the handling and filling of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2. 1.3 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.4 This Standard is written in SI units except for the cylinder marking requirements, where the service pressure and, where applicable (e.g., Specification TC-39M), the test pressure are expressed in bar or pounds per square inch gauge (psig). However, for consistency in the design and test requirements of all containers, MPa and kPa have been retained as units to express service pressure. Considering the use of the "bar" unit by ISO (International Organization for Standardization) to mark service and test pressures, it was decided to use the same unit for marking service pressure in this Standard. When the capital letter "M" has been added to a specification designation, it identifies that the container specification is metricated.
국제분류(ICS)코드
페이지수 73
Edition

이력정보

No. 표준번호 표준명 발행일 상태
1 CSA B340:25상세보기 Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2 2025-01-01 표준
2 B340-18상세보기 Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2 2018-01-01 폐지
3 B340-18 (R2023)상세보기 Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2 2018-01-01 표준
4 B340-14상세보기 Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, class 2 2014-01-01 표준
5 ASTM B340-61(1977)e1상세보기 Test Method for Surety of Make of Electrical Contact Materials 1977-01-01 폐지

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)