한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

상세정보

분야
적용범위 Preface This is the seventh edition of CSA S16, Design of steel structures. It supersedes the previous limit states editions published in 2001, 1994, 1989, 1984, 1978, and 1974. These seven limit states design editions were preceded by seven working stress design editions published in 1969, 1965, 1961, 1954, 1940, 1930, and 1924. The 1969 working stress design edition was withdrawn in 1984, from which point the design of steel structures in Canada has been carried out using limit states design principles. This Standard is appropriate for the design of a broad range of structures. It sets out minimum requirements and is expected to be used only by engineers competent in the design of steel structures. Scope ? 1.1 General This Standard provides rules and requirements for the design, fabrication, and erection of steel structures. The design is based on limit states. The term "steel structures" refers to structural members and frames that consist primarily of structural steel components, including the detail parts, welds, bolts, or other fasteners required in fabrication and erection. This Standard also applies to structural steel components in structures framed in other materials. The clauses related to fabrication and erection, serve to show that design is inextricably a part of the design-fabrication-erection sequence and cannot be considered in isolation. For matters concerning standard practice pertinent to the fabrication and erection of structural steel not covered in this Standard, see Annex A. 1.2 Requirements? Requirements for steel structures such as bridges, antenna towers, offshore structures, and cold-formed steel structural members are given in other CSA Standards. 1.3 Application This Standard applies unconditionally to steel structures, except that supplementary rules or requirements may be necessary for (a) unusual types of construction; (b) mixed systems of construction; (c) steel structures that (i) have great height or spans; (ii) are required to be movable or be readily dismantled; (iii) are exposed to severe environmental conditions; (iv) are exposed to severe loads such as those resulting from vehicle impact or explosion; (v) are required to satisfy aesthetic, architectural, or other requirements of a non-structural nature; (vi) employ materials or products not listed in Clause 5; or (vii) have other special features that could affect the design, fabrication, or erection; (d) tanks, stacks, other platework structures, poles, and piling; and (e) crane-supporting structures. 1.4 Other standards The use of other standards for the design of members or parts of steel structures is neither warranted nor acceptable except where specifically directed in this Standard. The formulas provided in this Standard may be supplemented by a rational design based on theory, analysis, and engineering practice acceptable to the regulatory authority, provided that nominal margins (or factors) of safety at least equal to those intended in the provisions of this Standard are maintained. (See Annex B.)
국제분류(ICS)코드
페이지수 234
Edition

이력정보

No. 표준번호 표준명 발행일 상태
1 CSA S16:24상세보기 Design and construction of steel structures 2024-01-01 표준
2 CSA S16:19상세보기 Design of steel structures 2019-01-01 표준
3 S16-14 (R2019)상세보기 Design of steel structures 2014-01-01 표준
4 CSA S16-09상세보기 Design of steel structures 2009-01-01 폐지

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)