사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
CSA IEC 61000-4-30:16 (R2021)
Electromagnetic compatibility (EMC) — Part 4-30: Testing and measurement techniques — Power quality measurement methods (Adopted IEC 61000-4-30:2015, third edition, 2015-02) | Compatibilité électromagnétique (CEM) — Partie 4-30 : Techniques d’essai et de- 발행일 : 2016-01-01
- 발행기관 : CSA
상세정보
| 분야 | 11 : LG Electronics |
|---|---|
| 적용범위 | Preface This is the third edition of CAN/CSA-IEC 61000-4-30, Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods, which is an adoption without modification of the identically titled IEC (International Electrotechnical Commission) Standard 61000-4-30 (third edition, 2015-02). It supersedes the previous edition published in 2010 as CAN/CSAC61000-4-30 (adopted IEC 61000-4-30:2008).? Scope This part of IEC 61000-4 defines the methods for measurement and interpretation of results for power quality parameters in a.c. power supply systems with a declared fundamental frequency of 50 Hz or 60 Hz.? Measurement methods are described for each relevant parameter in terms that give reliable and repeatable results, regardless of the method's implementation. This standard addresses measurement methods for in-situ measurements.? Measurement of parameters covered by this standard is limited to conducted phenomena in power systems. The power quality parameters considered in this standard are power frequency, magnitude of the supply voltage, flicker, supply voltage dips and swells, voltage interruptions, transient voltages, supply voltage unbalance, voltage harmonics and interharmonics, mains signalling on the supply voltage, rapid voltage changes, and current measurements. Emissions in the 2 kHz to 150 kHz range are considered in Annex C (informative), and over- and under deviations are considered in Annex D (informative). Depending on the purpose of the measurement, all or a subset of the phenomena on this list may be measured.? NOTE 1 Test methods for verifying compliance with this standard can be found in IEC 62586-2.? NOTE 2 The effects of transducers inserted between the power system and the instrument are acknowledged but not addressed in detail in this standard. Guidance about effects of transducers can be found IEC TR 61869-103.? --------------------------------------------------------------------------------------------------------------------------------? Pr?face Ce document constitue la troisi?me ?dition de la CAN/CSA-IEC 61000-4-30, Compatibilit? ?lectromagn?tique (CEM) - Partie 4-30 : Techniques d'essai et de mesure - M?thodes de mesure de la qualit? de l'alimentation. II s'agit de l'adoption, sans modifications, de la norme IEC (Commission ?lectrotechnique Internationale) 61000-4-30 (troisi?me ?dition, 2015-02) qui porte le m?me titre. Cette norme remplace l'?dition ant?rieure publi?e en 2010 qui portait la d?signation CAN/CSA-C61000-4-30 (norme IEC 61000-4-30:2008 adopt?e).? Domaine d'application La pr?sente partie de l'IEC 61000-4 d?finit les m?thodes de mesure des param?tres de qualit? de l'alimentation des r?seaux d'?nergie ?lectrique en courant alternatif ? une fr?quence fondamentale d?clar?e de 50 Hz ou 60 Hz et la fa?on d'interpr?ter les r?sultats.? Les m?thodes de mesure sont d?crites pour chaque param?tre applicable en des termes qui fournissent des r?sultats fiables et r?p?titifs ind?pendamment de la mise en oeuvre de la m?thode. La pr?sente norme porte sur les m?thodes de mesure destin?es aux mesurages in situ.? Le mesurage des param?tres couverts par la pr?sente norme se limite aux ph?nom?nes conduits sur les r?seaux d'?nergie ?lectrique. Les param?tres de qualit? de l'alimentation pris en compte dans la pr?sente norme sont la fr?quence industrielle, l'amplitude de la tension d'alimentation, le papillotement (?flicker?), les creux et les surtensions temporaires d'alimentation, les coupures de tension, les tensions transitoires, le d?s?quilibre de tension d'alimentation, les harmoniques et interharmoniques de tension, les signaux transmis sur la tension d'alimentation, les variations rapides de tension et les mesurages de courant. Les ?missions dans la plage comprise entre 2 kHz et 150 kHz sont prises en compte dans l'Annexe C (informative), et les valeurs hautes et valeurs basses sont prises en compte dans l'Annexe D (informative). En fonction de l'objet du mesurage, les mesurages peuvent porter soit sur une partie des ph?nom?nes de cette liste, soit sur l'ensemble.? NOTE 1 Les m?thodes d'essai concernant la v?rification de la conformit? ? la pr?sente norme se trouvent dans l'IEC 62586-2.? NOTE 2 Les effets des transducteurs lorsqu'ils sont plac?s entre le r?seau et l'appareil de mesure sont pris en compte mais non trait?s en d?tail dans la pr?sente norme. Des lignes directrices sur les effets des transducteurs peuvent ?tre consult?es dans l'IEC TR 61869-103. |
| 국제분류(ICS)코드 | |
| 페이지수 | 174 |
| Edition |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | IEC 61000-4-30:2015/AMD1:2021상세보기 | Amendment 1 - Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2021-03-04 | 표준 |
| 2 | IEC 61000-4-30:2015+AMD1:2021 CSV상세보기 | Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2021-03-04 | 표준 |
| 3 | IEC 61000-4-30:2015/COR1:2016상세보기 | Corrigendum 1 - Electromagnetic compatibility (EMC) - Part 3-40: Testing and measurement techniques - Power quality measurement methods | 2016-12-15 | 표준 |
| 4 | CSA IEC 61000-4-30:16 (R2021)상세보기 | Electromagnetic compatibility (EMC) — Part 4-30: Testing and measurement techniques — Power quality measurement methods (Adopted IEC 61000-4-30:2015, third edition, 2015-02) | Compatibilité électromagnétique (CEM) — Partie 4-30 : Techniques d’essai et de | 2016-01-01 | 표준 |
| 5 | IEC 61000-4-30:2015상세보기 | Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2015-02-20 | 표준 |
| 6 | IEC 61000-4-30:2015 RLV상세보기 | Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2015-02-20 | 표준 |
| 7 | IEC 61000-4-30:2008상세보기 | Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2008-10-13 | 구판 |
| 8 | IEC 61000-4-30:2003/COR1:2006상세보기 | Corrigendum 1 - Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2006-08-15 | 구판 |
| 9 | IEC 61000-4-30:2003상세보기 | Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods | 2003-02-11 | 구판 |
관련상품
- IEC TR 61000-2-1:1990 - Electromagnetic compatibility (EMC) - Part 2: Environment - Section 1: Description of the environment - Electromagnetic environment for low-frequency conducted disturbances and signalling in public power supply systems
- IEC TR 61000-2-3:1992 - Electromagnetic compatibility (EMC) - Part 2: Environment - Section 3: Description of the environment - Radiated and non-network-frequency-related conducted phenomena
- IEC 61000-4-12:1995 - Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 12: Oscillatory waves immunity test. Basic EMC Publication
- IEC TR 61000-2-6:1995 - Electromagnetic compatibility (EMC) - Part 2: Environment - Section 6: Assessment of the emission levels in the power supply of industrial plants as regards low-frequency conducted disturbances
- IEC 61000-5-5:1996 - Electromagnetic compatibility (EMC) - Part 5: Installation and mitigation guidelines - Section 5: Specification of protective devices for HEMP conducted disturbance. Basic EMC Publication
다른 사람이 함께 구입한 상품
- 함께 구입한 상품이 존재하지 않습니다.
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)