사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
IEC TS 60034-18-33:2010
Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses- 발행일 : 2010-07-22
- 발행기관 : IEC
상세정보
| 분야 | TC 2 : Rotating machinery |
|---|---|
| 적용범위 | IEC/TS 60034-18-33:2010 describes procedures for evaluation of insulation systems by endurance testing where thermal and electrical stresses are applied simultaneously. The procedures are intended for insulation systems used in a.c. electrical machines using form-wound windings. The test procedures provide a comparison of performance between reference and candidate systems at combinations of voltage and temperature which have been used separately to assess quality in the past and which are chosen to produce failures within a suitable timescale and at stresses within practical limits. The outcome of the test on the candidate insulation system will indicate whether it is better or worse than the reference system with proven service experience. The main changes of this new edition with respect to the previous one are as follows: - the requirement to investigate the nature of interactions between thermal and electrical stresses has been abandoned; - the use of single stress acceleration factors has been removed; - the selection of stress levels has been adjusted and the temperatures are now related to the thermal class temperature of the insulation system; - the introduction of end-point criteria; - a simplified method to display results. |
| 국제분류(ICS)코드 | 29.160.01 : 회전기계 일반 |
| 페이지수 | 15 |
| Edition | 2.0 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | IEC TS 60034-18-33:2010상세보기 | Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses | 2010-07-22 | 표준 |
| 2 | IEC TS 60034-18-33:1995상세보기 | Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 33: Test procedures for form-wound windings - Multifactor functional evaluation - Endurance under combined thermal and electrical stresses of insulation systems used in machines up to and including 50 MVA and 15 kV | 1995-03-29 | 구판 |
관련상품
- IEC 60034-2:1972 - Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles)
- IEC 60034-2A:1974 - Rotating electrical machines - Part 2: Methods for determining losses and efficiency of rotating electrical machinery form tests (excluding machines for traction vehicles) - Measurement of losses by the calorimetric method
- IEC 60034-10:1975 - Rotating electrical machines. Part 10: Conventions for description of synchronous machines
- IEC 60034-13:1980 - Rotating electrical machines. Part 13: Specification for mill auxiliary motors
- IEC 60034-11-2:1984 - Rotating electrical machines - Part 11: Built-in thermal protection - Chapter 2: Thermal detectors and control units used in thermal protection systems
다른 사람이 함께 구입한 상품
- IEC 60034-18-34:2012 - Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
- IEC TS 60034-24:2009 - Rotating electrical machines - Part 24: Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide
- IEC 60034-16-1:2011 - Rotating electrical machines - Part 16-1: Excitation systems for synchronous machines - Definitions
- IEC 60034-15:2009 - Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
- IEC TS 60034-16-3:1996 - Rotating electrical machines - Part 16: Excitation systems for synchronous machines - Section 3: Dynamic performance
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)