사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ISO 14126:1999
Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction- 발행일 : 1999-09-09
- 발행기관 : ISO
상세정보
| 분야 | ISO/TC 61/SC 13 : Composites and reinforcement fibres |
|---|---|
| 적용범위 | 1.1 This International Standard specifies two methods for determining compressive properties, in directions parallel to the plane of lamination, of fibre-reinforced plastic composites. 1.2 The compressive properties are of interest for specifications and quality-control purposes. 1.3 Two loading methods and two types of specimen are described. They are: Method 1: provides shear loading of the specimen (gauge length unsupported). Method 2: provides end loading, or mixed loading, of the specimen (gauge length unsupported). NOTE For tabbed specimens end-loaded using method 2, some load is transferred into the specimen gauge length by shear through the tabs. Type A specimen: rectangular cross-section, fixed thickness, end-tabbed. Type B specimen: rectangular cross-section, range of thicknesses, untabbed or end-tabbed (two sizes available). Any combination of test method and specimen may be used, provided that the requirements of subclause 9.8 are satisfied and that the specimen is representative of the material under test. These alternative test conditions will not necessarily give the same result. The type A specimen is the preferred specimen for unidirectionally reinforced materials tested in the fibre direction. For other materials, the type A or B specimen may be used. The type B2 specimen is preferred for mat, fabric and other multidirectionally reinforced materials. 1.4 The methods are suitable for fibre-reinforced thermoplastic and thermosetting plastic composites. Unreinforced and particle-filled plastics, as well as those reinforced with short fibres (less than 1 mm in length), are covered by ISO 604 (see bibliography). 1.5 The methods are performed using specimens which may be machined from a test panel made in accordance with ISO 1268 or equivalent methods, or from finished or semi-finished products. 1.6 The methods specify required dimensions for the specimen. Tests which are carried out on specimens of other dimensions, or on specimens which are prepared under different conditions, may produce results which are not comparable. Other factors, such as the speed of testing, the support fixture used and the condition of the specimens, can influence the results. Consequently, when comparative data are required, these factors must be carefully controlled and recorded. 1.7 Fibre-reinforced plastics are usually anisotropic. It is therefore often useful to cut test specimens in at least the two main directions of anisotropy, or in directions previously specified (for example a lengthwise direction associated with the production process). |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 18 |
| Edition | 1 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 14126:2023상세보기 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction | 2023-10-13 | 표준 |
| 2 | ISO 14126:1999/Cor 1:2001상세보기 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction — Technical Corrigendum 1 | 2001-07-19 | 구판 |
| 3 | ISO 14126:1999상세보기 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction | 1999-09-09 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ISO 527-1:2019 - Plastics — Determination of tensile properties — Part 1: General principles
- ISO 527-4:2021 - Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
- ISO 14125:1998 - Fibre-reinforced plastic composites — Determination of flexural properties
- ISO 178:2019 - Plastics — Determination of flexural properties
- ISO 527-5:2021 - Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)