관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plain bearings — Thin-walled half bearings with or without flange — Part 3: Determination of the peripheral length
| 분야 | ISO/TC 123/SC 5 : Quality analysis and assurance |
|---|---|
| 적용범위 | This document specifies, according to ISO 12301, the checking of the peripheral length of thin-walled half bearings with or without flange, and describes the necessary checking methods and measuring equipment. Thin-walled half bearings are flexible and, in the free condition, do not conform to a cylindrical profile. This is one reason the peripheral length of the half bearings can only be measured under a constraining load by use of specialized measuring equipment. In addition, measuring equipment different from that illustrated in this document can be used, provided the measuring accuracy of the equipment is consistent with the specifications given in Clause 17. This document does not include the measurement of the parting line taper. This document applies to thin-walled half bearings, the specifications of which are given in ISO 3548‑1. |
| 국제분류(ICS)코드 | 21.100.10 : 평 베어링 |
| 페이지수 | 40 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 3548-3:2023 | Plain bearings — Thin-walled half bearings with or without flange — Part 3: Determination of the peripheral length | 2023-03-16 | 표준 |
| 2 | ISO 3548-3:2012 | Plain bearings — Thin-walled half bearings with or without flange — Part 3: Measurement of peripheral length | 2012-11-28 | 폐지 |
ISO 3548-1:2022/DAmd 1 - Plain bearings — Thin-walled half bearings with or without flange — Part 1: Tolerances, design features and methods of test — Amendment 1 상세보기
ISO 3548-3:2012 - Plain bearings — Thin-walled half bearings with or without flange — Part 3: Measurement of peripheral length 상세보기
ISO 3548-1:2014 - Plain bearings -- Thin-walled half bearings with or without flange -- Part 1: Tolerances, design features and methods of test 상세보기
ISO 3548-2:2020 - Plain bearings -- Thin-walled half bearings with or without flange -- Part 2: Measurement of wall thickness and flange thickness 상세보기
ISO 3548-1:2022 - Plain bearings — Thin-walled half bearings with or without flange — Part 1: Tolerances, design features and methods of test 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
