사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM D3276-00
Standard Guide for Painting Inspectors (Metal Substrates)- 발행일 : 2000-06-10
- 발행기관 : ASTM
상세정보
| 분야 | 06.02 : 페인트-제품 및 적용; 보호용 코팅 . 도관코팅 |
|---|---|
| 적용범위 | 1.1 This guide is intended as an information aid to painting inspectors in carrying out their task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to the specification of a particular job. Note 1-For additional helpful information, refer to the following documents: Manual of Coating Work for Light-Water Nuclear Power Plant Primary Containment and Other Safety-Related Facilities New Concepts for Coating Protection of Steel Structures SSPC-PA Guide 3 A Guide to Safety in Paint Application Steel Structures Painting Manual Vol 1 Good Painting Practice Steel Structures Painting Manual Vol 2 Systems and Specifications Manufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application) Material Safety Data Sheets (needed to ensure that personnel take necessary precautions in handling hazardous materials).1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This guide is arranged in the following order: Section Referenced Documents 2 ASTM Standards 2.1 OSHA Standards 2.2 Steel Structures Painting Council Pub- lications 2.3 Significance and Use 3 Preparation for Inspection 4 Field and Shop Inspection 5 Surface Preparation 5.1 Pictorial Standard D 2200 5.1.1 Factors Affecting Coating Perform- ance 5.2 Cleanliness 5.2.1 Mill Scale 5.2.2 Surface Profile 5.2.3 Cleaning Procedure 5.3 Chemical Cleaning 5.3.1 Solvent Vapor Cleaning 5.3.1.1 Hand Tool Cleaning 5.3.2 Power Tool Cleaning 5.3.3 Blast Cleaning 5.3.4 Cleaning and Preparation of Various Surfaces 5.4 Steel Surfaces 5.4.1 Galvanized Surfaces 5.4.2 Aluminum Surfaces 5.4.3 Precautions in Preparing Unpainted and Previously Painted Surfaces 5.4.4 Inspection of Surfaces Prior to Field Painting 5.5 New Construction 5.5.1 Maintenance Repainting 5.5.2 Inspection Equipment 6 General 6.1 Surface Profile Gages 6.1.1 Adhesion of Existing Coating 6.1.2 Portable Pull-off Adhesion Testers 6.1.3 Field Inspection Equipment 6.2 Drying and Curing Times 6.2.1 Thermometers 6.2.1.1 Dew Point 6.2.1.2 Coating Consistency 6.2.2 Consistency Cups 6.2.2.1 Weight-per-Gallon Cup 6.2.3 Wet-Film Thickness Gages 6.2.4 Interchemical Gage 6.2.4.1 Notched Gage 6.2.4.2 Dry-Film Thickness Gages 6.2.5 Tooke Gage 6.2.5.1 Nondestructive Film Thickness Gages 6.2.6 Magnetic-Type Gages 6.2.6.1 Coating Storage and Handling 7 Storage of Coating and Thinner 7.1 Mixing of Coatings 7.2 Thinning 7.3 Initial Samples 7.3.1 Thinning of Coating 7.3.2 Sampling of Thinned Coating 7.3.3 Heating of Coating 7.4 Weather Considerations 8 Drying 8.1 Low Temperature 8.2 High Temperature 8.3 Moisture 8.4 Wind 8.5 Coating Application 9 Residual Contaminants 9.1 Quality Assurance 9.2 Film Defects 9.2.1 Brush Application 9.3 Spray Application 9.4 Roller Application 9.5 Miscellaneous Methods 9.6 Rate of Application 9.7 Additional Considerations 10 Ventilation 10.1 Shopcoat Repair 10.2 Painting Schedule 10.3 Film Integrity 10.4 Recoat Time 10.5 Coating System Failure 10.6 Comparison of Surface Preparation Specifications Table 1 Inspection Checklist Appendix |
| 국제분류(ICS)코드 | |
| 페이지수 | 14 |
| Edition | 00 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3276-21상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2021-11-01 | 표준 |
| 2 | ASTM D3276-21 REDLINE상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2021-11-01 | 표준 |
| 3 | ASTM D3276-15e1상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2015-07-01 | 구판 |
| 4 | ASTM D3276-15상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2015-07-01 | 구판 |
| 5 | ASTM D3276-07상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2007-02-01 | 구판 |
| 6 | ASTM D3276-05상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2005-12-01 | 구판 |
| 7 | ASTM D3276-00상세보기 | Standard Guide for Painting Inspectors (Metal Substrates) | 2000-06-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- 함께 구입한 상품이 존재하지 않습니다.
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)