사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM F3298-19
Standard Specification for Design, Construction, and Verification of Lightweight Unmanned Aircraft Systems (UAS)- 발행일 : 2019-02-01
- 발행기관 : ASTM
상세정보
| 분야 | 15.09 : 종이, 회사 이미지용 상품 |
|---|---|
| 적용범위 | 1.1 This specification covers the airworthiness requirements for the design of light unmanned aircraft systems. This specification defines the baseline design, construction, and verification requirements for an unmanned aircraft system (UAS). 1.2 As a minimum, a UAS is defined as a system composed of the unmanned aircraft and all required on-board subsystems, payload, control station, other required off-board subsystems, any required launch and recovery equipment, all required crew members, and command and control (C2) links between UA and the control station. 1.3 The intent is for this standard of practice for CAA, self- or third-party determinations of airworthiness for UAS. This specification provides the core requirements for airworthiness certification of lightweight (UAS) (not necessarily limited to UAs under 55 lb GTOW) or for certain CAA operational approvals using risk-based categories. Additional requirements are envisioned to address the requirements for expanded operations and characteristics not addressed by this specification. 1.4 This specification is intended to support UAS operations. It is assumed that the risk of UAS will vary based on concept of operations, environment, and other variables. The fact that there are no human beings onboard the UAS may reduce or eliminate some hazards and risks. However, at the discretion of the CAA, this specification may be applied to other UAS operations. 1.5 The values in Imperial units are to be regarded as the standard. The values in SI are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 49.020 : 항공기 및 우주선 일반 |
| 페이지수 | 33 |
| Edition | 19 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3298-24상세보기 | Standard Specification for Design and Construction of Lightweight Unmanned Aircraft Systems (UAS) | 2024-05-01 | 표준 |
| 2 | ASTM F3298-24 REDLINE상세보기 | Standard Specification for Design and Construction of Lightweight Unmanned Aircraft Systems (UAS) | 2024-05-01 | 표준 |
| 3 | ASTM F3298-19상세보기 | Standard Specification for Design, Construction, and Verification of Lightweight Unmanned Aircraft Systems (UAS) | 2019-02-01 | 구판 |
| 4 | ASTM F3298-19 REDLINE상세보기 | Standard Specification for Design, Construction, and Verification of Lightweight Unmanned Aircraft Systems (UAS) | 2019-02-01 | 구판 |
| 5 | ASTM F3298-18상세보기 | Standard Specification for Design, Construction, and Verification of Fixed-Wing Unmanned Aircraft Systems (UAS) | 2018-05-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM F3442/F3442M-23 - Standard Specification for Detect and Avoid System Performance Requirements
- ASTM F3341/F3341M-23 - Standard Terminology for Unmanned Aircraft Systems
- ASTM F3478-20 - Standard Practice for Development of a Durability and Reliability Flight Demonstration Program for Low-Risk Unmanned Aircraft Systems (UAS) under FAA Oversight
- ASTM F2908-23 - Standard Specification for Unmanned Aircraft Flight Manual (UFM) for an Unmanned Aircraft System (UAS)
- ASTM F3548-21 - Standard Specification for UAS Traffic Management (UTM) UAS Service Supplier (USS) Interoperability
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)