관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 01.02 : 주철-철합금 |
---|---|
적용범위 | 1.1 This specification2 covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1). Note 1: Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M, low-alloy steel castings by Specification A217/A217M, and duplex stainless steel castings by Specification A995/A995M. 1.2 A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both. 1.2.1 Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800 °F [425 °C]. 1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M-specification designation (SI units), the inch-pound units shall apply. Within the text, the SI units are shown in brackets or parentheses. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 77.140.80 : 강 및 주철 및 단조 |
페이지수 | 7 |
Edition | 18e1 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM A351/A351M-24 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2024-05-01 | 표준 |
2 | ASTM A351/A351M-24 REDLINE | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2024-05-01 | 표준 |
3 | ASTM A351/A351M-18e1 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2018-05-01 | 구판 |
4 | ASTM A351/A351M-18 REDLINE | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2018-05-01 | 구판 |
5 | ASTM A351/A351M-18 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2018-05-01 | 구판 |
6 | ASTM A351/A351M-16 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2016-05-01 | 구판 |
7 | ASTM A351/A351M-15 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2015-09-01 | 구판 |
8 | ASTM A351/A351M-14 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2014-05-01 | 구판 |
9 | ASTM A351/A351M-13a | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2013-05-15 | 구판 |
10 | ASTM A351/A351M-13 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2013-05-01 | 구판 |
11 | ASTM A351/A351M-12b | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2012-11-01 | 구판 |
12 | ASTM A351/A351M-12a | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2012-09-01 | 구판 |
13 | ASTM A351/A351M-12 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2012-03-01 | 구판 |
14 | ASTM A351/A351M-10 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2010-04-01 | 구판 |
15 | ASTM A351/A351M-06 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2006-03-01 | 구판 |
16 | ASTM A351/A351M-05 | Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts | 2005-05-01 | 구판 |
17 | ASTM A351/A351M-03 | Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts | 2003-05-10 | 구판 |
18 | ASTM A351/A351M-00 | Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts | 2000-09-10 | 구판 |
19 | ASTM A351/A351M-94 | Standard Specification for Castings, Austenitic, Austenitic- Ferritic (Duplex), for Pressure-Containing Parts | 구판 |
관련상품이 존재하지 않습니다.
ASTM A216/A216M-18 - Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service 상세보기
ASTM A276/A276M-17 - Standard Specification for Stainless Steel Bars and Shapes 상세보기
ASTM A352/A352M-18a - Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature Service 상세보기
ASTM A36/A36M-19 - Standard Specification for Carbon Structural Steel 상세보기
ASTM A193/A193M-20 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기