한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D93-18 REDLINE

    Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
    • 발행일 : 2018-07-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF(레드라인) 144,300원

    • [영어]PRINT(레드라인) 144,300원

  • 레드라인이란?

    최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.

상세정보

분야
적용범위

1.1 These test methods cover the determination of the flash point of petroleum products in the temperature range from 40 °C to 370 °C by a manual Pensky-Martens closed-cup apparatus or an automated Pensky-Martens closed-cup apparatus, and the determination of the flash point of biodiesel in the temperature range of 60 °C to 190 °C by an automated Pensky-Martens closed cup apparatus.

Note 1: Flash point determinations above 250 °C can be performed, however, the precision has not been determined above this temperature. For residual fuels, precision has not been determined for flash points above 100 °C. The precision of in-use lubricating oils has not been determined. Some specifications state a D93 minimum flash point below 40 °C, however, the precision has not been determined below this temperature.

1.2 Procedure A is applicable to distillate fuels (diesel, biodiesel blends, kerosine, heating oil, turbine fuels), new and in-use lubricating oils, and other homogeneous petroleum liquids not included in the scope of Procedure B or Procedure C.

1.3 Procedure B is applicable to residual fuel oils, cutback residua, used lubricating oils, mixtures of petroleum liquids with solids, petroleum liquids that tend to form a surface film under test conditions, or are petroleum liquids of such kinematic viscosity that they are not uniformly heated under the stirring and heating conditions of Procedure A.

1.4 Procedure C is applicable to biodiesel (B100). Since a flash point of residual alcohol in biodiesel is difficult to observe by manual flash point techniques, automated apparatus with electronic flash point detection have been found suitable.

1.5 These test methods are applicable for the detection of contamination of relatively nonvolatile or nonflammable materials with volatile or flammable materials.

1.6 The values stated in SI units are to be regarded as the standard.

1.6.1 Exception—The values given in parentheses are for information only.

Note 2: It has been common practice in flash point standards for many decades to alternately use a C-scale or an F-scale thermometer for temperature measurement. Although the scales are close in increments, they are not equivalent. Because the F-scale thermometer used in this procedure is graduated in 5 °F increments, it is not possible to read it to the 2 °C equivalent increment of 3.6 °F. Therefore, for the purposes of application of the procedure of the test method for the separate temperature scale thermometers, different increments must be used. In this test method, the following protocol has been adopted: When a temperature is intended to be a converted equivalent, it will appear in parentheses following the SI unit, for example 370 °C (698 °F). When a temperature is intended to be a rationalized unit for the alternate scale, it will appear after “or,” for example, 2 °C or 5 °F.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.4, 7.1, 9.3, 9.4, 11.1.2, 11.1.4, 11.1.8, 11.2.2, and 12.1.2.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드
페이지수 18
Edition 18

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D93-20상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2020-08-01 표준
2 ASTM D93-20 REDLINE상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2020-08-01 표준
3 ASTM D93-19상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2019-11-01 구판
4 ASTM D93-19 REDLINE상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2019-11-01 구판
5 ASTM D93-18상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2018-07-01 구판
6 ASTM D93-18 REDLINE상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2018-07-01 구판
7 ASTM D93-16a상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2016-10-01 구판
8 ASTM D93-16상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2016-06-01 구판
9 ASTM D93-15a상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2015-10-15 구판
10 ASTM D93-15상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2015-01-01 구판
11 ASTM D93-13e1상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2013-07-15 구판
12 ASTM D93-13상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2013-07-15 구판
13 ASTM D93-12상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2012-11-01 구판
14 ASTM D93-11상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2011-10-01 구판
15 ASTM D93-10a상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2010-10-01 구판
16 ASTM D93-10상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2010-02-15 구판
17 ASTM D93-09상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2009-12-15 구판
18 ASTM D93-08상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2008-10-15 구판
19 ASTM D93-07상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2007-05-01 구판
20 ASTM D93-06상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 2006-11-01 구판
21 ASTM D93-02a상세보기 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester 2002-12-10 구판
22 ASTM D93-02상세보기 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester 2002-06-10 구판
23 ASTM D93-00상세보기 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester 2000-08-10 구판
24 ASTM D93-97상세보기 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester 구판
25 ASTM D93-90e1상세보기 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester 구판
26 ASTM D93-85상세보기 Standard Test Method for Flash Point by Pensky-Martens Closed Tester 구판
27 ASTM D93-94상세보기 Standard Test Method for Flash Point by Pensky-Martens Closed Tester 구판
28 ASTM D93-80e1상세보기 Standard Test Methods for Flash Point By Pensky-Martens Closed Tester 구판
29 ASTM D93-71상세보기 Standard Method Of Test For Flash Point By Pensky-Martens Closed Tester 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)