사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM D1004-21 REDLINE
Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting- 발행일 : 2021-01-15
- 발행기관 : ASTM
-
레드라인이란?
최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.
상세정보
| 분야 | |
|---|---|
| 적용범위 | 1.1?This test method2 covers the determination of the tear resistance of flexible plastic film and sheeting at very low rates of loading, 51 mm (2 in.)/min. and is designed to measure the force to initiate tearing. The specimen geometry of this test method produces a stress concentration in a small area of the specimen. The maximum stress, usually found near the onset of tearing, is recorded as the tear resistance in newtons (or pounds-force). The method is not applicable for film or sheeting material where brittle failures occur during testing or where maximum extension is greater than 101.6 mm (4 in.). 1.1.1?Although resistance to tear can be expressed in newtons per microns, (pounds-force per mil) of specimen thickness, this is only advisable where correlation for the particular material being tested has been established. In most cases, comparison between films of dissimilar thickness is not valid. Note 1:?Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.). 1.2?Constant-Rate-of-Grip Separation Test?This test method employs a constant rate of separation of the grips holding the test specimen. 1.2.1?Specimen extension shall be measured in this test method by grip separation. 1.3?The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2:?There is no known ISO equivalent to this standard. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 5 |
| Edition | 21 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1004-21상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2021-01-15 | 표준 |
| 2 | ASTM D1004-21 REDLINE상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2021-01-15 | 표준 |
| 3 | ASTM D1004-13 REDLINE상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2013-04-01 | 구판 |
| 4 | ASTM D1004-13상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2013-04-01 | 구판 |
| 5 | ASTM D1004-09상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2009-05-01 | 구판 |
| 6 | ASTM D1004-08상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2008-11-01 | 구판 |
| 7 | ASTM D1004-07상세보기 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2007-04-01 | 구판 |
| 8 | ASTM D1004-03상세보기 | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting | 2003-01-10 | 구판 |
| 9 | ASTM D1004-94a(2003)상세보기 | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting | 2003-01-10 | 구판 |
| 10 | ASTM D1004-94a상세보기 | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting | 1994-01-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- JIS K 6261-2:2017 - Rubber, vulcanized or thermoplastic -- Determination of low-temperature properties -- Part 2: Low-temperature brittleness
- KS M ISO 1924-3 - 종이 및 판지 — 인장 특성의 측정 —제3부: 정속 신장법(100 mm/min)
- ASTM D4169-22 REDLINE - Standard Practice for Performance Testing of Shipping Containers and Systems
- ASTM F88/F88M-21 REDLINE - Standard Test Method for Seal Strength of Flexible Barrier Materials
- JIS K 6259-1:2015 - Rubber, vulcanized or thermoplastic -- Determination of ozone resistance -- Part 1: Static and dynamic strain testing
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)