사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
IEC 62040-3:2011
Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements- 발행일 : 2011-03-14
- 발행기관 : IEC
- 대체표준 : IEC 62040-3:2021
상세정보
| 분야 | TC 22/SC 22H : Uninterruptible power systems (UPS) |
|---|---|
| 적용범위 | IEC 62040-3:2011 applies to movable, stationary and fixed electronic uninterruptible power systems (UPS) that deliver single or three phase fixed frequency a.c. output voltage not exceeding 1 000 V a.c. and that incorporate an energy storage system, generally connected through a d.c. link. This standard is intended to specify performance and test requirements of a complete UPS and not of individual UPS functional units. The individual UPS functional units are dealt with in IEC publications referred to in the bibliography that apply so far that they are not in contradiction with this standard. The primary function of the UPS covered by this standard is to ensure continuity of an a.c. power source. The UPS may also serve to improve the quality of the power source by keeping it within specified characteristics. UPS have been developed over a wide range of power, from less than hundred watts to several megawatts, to meet requirements for availability and quality of power to a variety of loads. Refer to Annexes A and B for information on typical UPS configurations and topologies. This standard also covers UPS test and performance when power switches form integral part of a UPS and are associated with its output. Included are interrupters, bypass switches, isolating switches, and tie switches. These switches interact with other functional units of the UPS to maintain continuity of load power. This standard does not cover: - conventional a.c. input and output distribution boards or d.c. boards and their associated switches (e.g. switches for batteries, rectifier output or inverter input); - stand-alone static transfer systems covered by IEC 62310-3; - systems wherein the output voltage is derived from a rotating machine. NOTE 1 This standard recognises that power availability to information technology (IT) equipment represents a major UPS application. The UPS output characteristics specified in this standard are therefore also aimed at ensuring compatibility with the requirements of IT equipment. This, subject any limitation stated in the manufacturer's declaration, includes requirements for steady state and transient voltage variation as well as for the supply of both linear and non-linear load characteristics of IT equipment. NOTE 2 Test loads specified in this standard simulate both linear and non-linear load characteristics. Their use is prescribed with the objective of verifying design and performance, as declared by the manufacturer, and also of minimising any complexity and energy consumption during the tests. NOTE 3 This standard is aimed at 50 Hz and 60 Hz applications but does not exclude other frequency applications within the domain of IEC 60196. This is subject to an agreement between manufacturer and purchase in respect to any particular requirements arising. NOTE 4 Single phase and three-phase voltage UPS covered by this standard include without limitation UPS supplying single-phase, two-wire; single-phase, three-wire; two-phase, three-wire, three-phase, three-wire and three-phase, four-wire loads. This second edition cancels and replaces first edition published in 1999 and constitutes a technical revision. The significant technical changes are: - reference test load - definition and application revised (3.3.5 and 6.1.1.3); - test schedule - presented as a single table grouped by revised type and routine tests (see 6.1.6, Table 3); - dynamic output voltage performance characteristics - guidance to measure - addition (Annex H); - UPS efficiency - requirements and methods of measure - addition (Annexes I and J); - functional availability - guidance for UPS reliability integrity level classification - addition (Annex K). |
| 국제분류(ICS)코드 | 29.200 : 정류기. 변환기. 안정된 동력공급원 |
| 페이지수 | 214 |
| Edition | 2.0 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | IEC 62040-3:2021상세보기 | Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements | 2021-04-21 | 표준 |
| 2 | IEC 62040-3:2011/COR1:2011상세보기 | Corrigendum 1 - Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements | 2011-09-13 | 구판 |
| 3 | IEC 62040-3:2011상세보기 | Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements | 2011-03-14 | 구판 |
| 4 | IEC 62040-3:1999/COR1:2003상세보기 | Corrigendum 1 - Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements | 2003-07-31 | 구판 |
| 5 | IEC 62040-3:1999상세보기 | Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements | 1999-03-31 | 구판 |
관련상품
- IEC 62040-1-2:2002 - Uninterruptible power systems (UPS) - Part 1-2: General and safety requirements for UPS used in restricted access locations
- IEC 62040-1-1:2002 - Uninterruptible power systems (UPS) - Part 1-1: General and safety requirements for UPS used in operator access areas
- IEC 62040-1-2:2002/COR1:2002 - Corrigendum 1 - Uninterruptible power systems (UPS) - Part 1-2: General and safety requirements for UPS used in restricted access locations
- IEC 62040-1-1:2002/COR1:2002 - Corrigendum 1 - Uninterruptible power systems (UPS) - Part 1-1: General and safety requirements for UPS used in operator access areas
- IEC 62040-1-1:2002/COR2:2004 - Corrigendum 2 - Uninterruptible power systems (UPS) - Part 1-1: General and safety requirements for UPS used in operator access areas
다른 사람이 함께 구입한 상품
- IEC 62040-1:2017 - Uninterruptible power systems (UPS) - Part 1: Safety requirements
- IEC 62040-2:2016 - Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements
- IEC 60146-1-1:2009 - Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements
- IEC 60034-30:2008 - Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
- IEC 60076-15:2015 - Power transformers - Part 15: Gas-filled power transformers
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)