사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
IEC 60034-18-31:2012
Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines- 발행일 : 2012-06-25
- 발행기관 : IEC
상세정보
| 분야 | TC 2 : Rotating machinery |
|---|---|
| 적용범위 | IEC 60034-18-31:2012 describes thermal endurance test procedures for classification of insulation systems used in a.c. or d.c. rotating electrical machines with indirect cooling and form-wound windings. These test procedures are intended to compare the thermal endurance performance of the mainwall insulation between conductor(s) and ground and, where required by the design of the coil or bar, the insulation between the turns. The main technical changes with regard to the previous edition include: - Definition of the test method and sub-cycles required to establish a consistent standardized platform for thermal ageing of insulation systems for form-wound windings. - Recommendations for establishing a thermal life curve based on confidence intervals. - Comparison of candidate and reference system performance for specific requirements of thermal class, within feasible limits. Keywords: rotating machinery, insulation systems |
| 국제분류(ICS)코드 | 29.160.01 : 회전기계 일반 |
| 페이지수 | 54 |
| Edition | 2.0 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | IEC 60034-18-31:2012상세보기 | Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines | 2012-06-25 | 표준 |
| 2 | IEC 60034-18-31:1992/AMD1:1996상세보기 | Amendment 1 - Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 31: Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in machines up to and including 50 MVA and 15 kV | 1996-11-28 | 구판 |
| 3 | IEC 60034-18-31:1992상세보기 | Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 31: Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in machines up to and including 50 MVA and 15 kV | 1992-07-31 | 구판 |
관련상품
- IEC 60034-2:1972 - Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles)
- IEC 60034-2A:1974 - Rotating electrical machines - Part 2: Methods for determining losses and efficiency of rotating electrical machinery form tests (excluding machines for traction vehicles) - Measurement of losses by the calorimetric method
- IEC 60034-10:1975 - Rotating electrical machines. Part 10: Conventions for description of synchronous machines
- IEC 60034-13:1980 - Rotating electrical machines. Part 13: Specification for mill auxiliary motors
- IEC 60034-11-2:1984 - Rotating electrical machines - Part 11: Built-in thermal protection - Chapter 2: Thermal detectors and control units used in thermal protection systems
다른 사람이 함께 구입한 상품
- IEC TS 60034-18-33:2010 - Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
- IEC 60034-18-34:2012 - Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
- IEC 60034-18-1:2010 - Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
- IEC TS 60034-24:2009 - Rotating electrical machines - Part 24: Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide
- IEC 60034-15:2009 - Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)